Gerenuk



GLG class “F”: Model Gerenuk 500 3D A powerful multi-purpose lift with remote control 
The Gerenuk 500 3D is a glass handler and installer without wheels for use with a host vehicle such as a mobile crane. With the 3D-head the Gerenuk has the same flexible pattern of movements as the ground based glass lifts. Standard equipped with suction cups. 

Comparable models
- The 500-kilos Gerenuk lift is not sharing chassis with any of the other glass lifts which are all mounted with wheels 

Gerenuk 500 is mounted on host vehicle such as
 
- fork trucks 
- telescopic handlers 
- mobile cranes 
- rough terrain fork trucks 

Radio remote control
 
- standard equipped with radio remote control.
- The radio remote control provides 5 speed settings for increased efficiency and precision handling. 
- full functionality of boom extend/retract of 43 centimeters/17 inches  
- boom side swing left/right 20 centimeters/8 inches 
- boom lift/lower 
- tilt boom tip forward/backward 
- articulate boom tip left/right for side load transport rotate panel 180 degrees clockwise/counter clockwise directions 

We recommend the lift
 - ideal for outside installations on high rise buildings with difficult access like balconies 

The GLG 500 SPR-3D in short
A 60 meters high mobile crane is a perfect aid for lifting window panels high but can be a bit rough and crude when it comes to installing the window. Here the combination with the Gerenuk lift is ideal for precise installations on high rise buildings. As it has the same flexible pattern of movements as our ground based glass lifts, it’s perfect for quick, precise and flexible mounting even with difficult access to the window frame like balconies

Click to see printable PDF

GLG680 SPR-3D



GLG class “C”: Model 680 SPR-3D

A powerful all-terrain multi-purpose lift with remote control

The GLG 680 SPR-3D is a cross country mobile glass handler capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement weighing as much as 680 kilos/1499 lbs and lift as high as 4 meters/13.1ft overhead. Standard equipped with suction cups.

Comparable models
- Model 550 SP-3D is a more affordable ‘680 SPR-3D’, but without remote control and a shorter boom
 
Radio remote control
 
- The 680-kilos machine is standard equipped with radio remote control

Self propelled
- a battery electric hydrostatic drive for all terrains

Hydraulic controls provides the operator with the ability to  
- feather panels to the millimetre into the opening

The hydraulic 3D-head provides millimetre precise movements in all 3 dimensions
 
- hydraulically rotate the boom tip to the side for narrow access areas
- hydraulically pick up panel from a flat position up to 60 centimeters/23 inches under ground level
- swing it more than 180 degrees and lift and mount as high as 4,0 meters/13.1ft over ground level  
-tilt boom tip forward/backward

Hydraulic telescopic boom and hydraulic side shift
- Extend/retract boom tip up to 120 centimeters/47 inches
- 20 centimeters/8 inches of hydraulic side shift
- this lift offer the largest lift capacity with booms fully extended on the market


Full weight in full height
-
no outriggers required
- lifts the full rated capacity to the maximum lift height of 4,0 meters/13.1ft

Side load transport  
- swing load to left or right side of the machine for narrow aisle passage  
- side load capacity is 400 kilos/880lbs with dual wheels installed

Reduced overall width  
- outside wheel of dual wheel can be removed for 82 centimeters/32 inch overall width

We recommend the lift for
-
odd jobs with challenging access
- rough terrain-jobs
- for glaziers wanting to minimize situations where crane aid is necessary
- mounting of big window with small crew/one man jobs
- for jobs where full lift capacity in full height is needed
- for indoor installations with single-wheels
- heavy fire door and wall mounting inside and outside
- use with unique grabber.

The GLG 680 SPR-3D in short
This remote controlled lift is taking glass lifts to the next level. It is perfect for stable handling and mounting of large, challenging panels. It’s strong as an ox and has all the features for quick, precise and flexible mounting. Can be equipped with multiple purpose suction disks, forks, hook and a hydraulic pipe grabber.


Click to see printable PDF

GLG550 SPR-3D



GLG class “D”: Model 550 SPR-3D

A remote controlled all-terrain multi-purpose glass lift

The GLG 550 SPR-3D-model is not on stock, but is being produced on demand.
Ask our sales directors for further information.

The GLG 550 SP-3D
is a remote controlled cross country mobile glass handler capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement weighing as much as 550kgs/1212lbs and lift as high as 4 meters/13.1ft overhead. Standard equipped with suction cups.

Comparable models
- Check the 680-model for introduction to our remote control system.
- In all other aspects, the remote controlled version of our 550-kilos machine is identical with the GLG 550 SP-3D. See this for an introduction.


Click to see printable PDF

GLG500 SPR-3D



GLG class “D”: Model 500 SPR-3D A powerful multi-purpose lift with remote control

The GLG 500 SPR-3D is a mobile glass handler with telescopic front axels capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement weighing as much as 500 kilos/1102 lbs and lift as high as 5 meters/16.4 ft overhead. Standard equipped with suction cups.

Comparable models

- The 500-kilos lift is not sharing chassis with any of the other glass lifts, closest are the 680 SPR-3D and 425 SP-3D.

Radio remote control

- standard equipped with radio remote control.
- the radio remote control provides 5 speed settings for increased efficiency and precision handling.
- full functionality of boom extend/retract and boom swing left/right (7 to 45 degrees based on axle extensions)
- boom lift/lower tilt boom tip forward/backward
- articulate boom tip left/right for side load transport  
- rotate panel 180 degrees clockwise/counter clockwise directions

Self propelled

- a battery electric drive primary for indoor use.

Telescopic front axles

- Telescopic front axles in lieu of outriggers for increased mobility
- Safety surveillance system

Full weight in full height
 
- lifts the full rated capacity to the maximum lift height of 5,0 meters/16.4 ft overhead

We recommend the lift
 
- ideal for inside-out installations in high rise buildings

The GLG 500 SPR-3D in short
This remote controlled lift is ideal for inside-out installations in high rise buildings increasing window installation productivity significantly. It is perfect for handling and mounting of large, challenging panels. It has all the features for quick, precise and flexible mounting. Can be equipped with multiple purpose suction disks, forks and hooks.


Click to see printable PDF

GLG425 SPR-3D



GLG class “B”: Model 425 SPR-3D
A remote controlled all terrain multi purpose glass lift  

The GLG 425 SPR-3D
model is not on stock, but is being produced on demand.
Ask our sales directors for further information.

The GLG 425 SP-3D
is a remote controlled self propelled battery electric drive mobile glass handler capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement of 425kilos/935 lbs. Standard equipped with suction cups.

Comparable models
- Check the 680-model for introduction to our remote control system.
- In all other aspects, the remote controlled version of our 425-kilos machine is identical with the GLG 425 SP-3D.
- See this for an introduction.


Click to see printable PDF

GLG550 SP-3D



GLG class “C”: Model 550 SP-3D A powerful all terrain multi purpose glass lift

The GLG 550 SP-3D is a cross country mobile glass handler capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement weighing as much as 550kgs/1212lbs and lift as high as 4 meters/13.1ft overhead. Standard equipped with suction cups.

Comparable models

- Model 550 SP-3D is a more affordable ‘680 SPR-3D’, but comes without remote control and a longer boom
- The 550 can be special ordered with remote control

Self propelled
- a battery electric hydrostatic drive for all terrains

Hydraulic controls provides the operator with the ability to
- feather panels to the millimetre into the opening

The hydraulic 3D-head provides millimetre precise movements in all 3 dimensions
- hydraulically rotate the boom tip to the side for narrow access areas
- hydraulically pick up panel from a flat position up to 60 centimeters/23 inches under ground level, swing it more than 180 degrees and lift and mount as high as 4,0 meters/13.1ft over ground level
- tilt boom tip forward/backward

Hydraulic telescopic boom and hydraulic side shift

- Extend/retract boom tip up to 50 centimeters/20 inches
- 20 centimeters/8 inches of hydraulic side shift
- this lift offer the largest lift capacity with booms fully extended on the market

Side load transport

- swing load to left or right side of the machine for narrow aisle passage
- side load capacity is 400 kilos/880lbs with dual wheels installed

Reduced overall width
 
- outside wheel of dual wheel can be removed for 82 centimeters/32 inch overall width

We recommend the lift for
-
odd jobs with challenging access
- rough terrain-jobs
- for glaziers wanting to minimize situations where crane aid is necessary
- mounting of big window with small crew/one man jobs
- for jobs where full lift capacity in full height is needed
- for indoor installations with single-wheels
- heavy fire door and wall mounting inside and outside
- use with unique grabber

The GLG 550 SP-3D in short
The 550-kilos lift is sharing chassis with the 680-kilos lift, two machines taking glass lifts to the next level. They are a perfect for stable handling and mounting of large, challenging panels. This is a very powerful lift and it has all the features for quick, precise and flexible mounting. Can be equipped with multiple purpose suction disks, forks, hook and a hydraulic pipe grabber.


Click to see printable PDF

GLG425 SP-3D



GLG class “B”: Model 425 SP-3D
Our bestseller – a compact, flexible self propelled glass lift


The GLG 425 SP-3D is a Self Propelled battery electric drive mobile glass handler capable of picking and transporting. With it’s 3D-head it’s capable of extreme precision placement of 425kilos/935 lbs. Standard equipped with suction cups.

Comparable models
- Model 420 SP is an more affordable ‘425 SP 3D’, but comes without a build-in telescopic arm and a 3D-head for mounting.
- The 425 can be special ordered with remote control

Hydraulic controls provides the operator with the ability to  
- feather panels to the millimetre into the opening

The hydraulic 3D-head provides millimetre precise movements in all 3 dimensions  
- hydraulically rotate panel 180 degrees clockwise or counter clockwise
- hydraulically pick up panel from a flat position up to 50 centimeters/1.7 ft under ground level,    
- swing it more than 180 degrees and lift and mount as high as 3,2 meters/10.5 ft over ground level  
- hydraulically swing load to left or right side of the machine for minimal access areas
- side load capacity is 100kg/220lbs

Manual side swing
-
manual side shift controls providing 80 centimeters/3.2 ft left/right from centre adjustments

Side load transport
swing load to left or right side of the machine for narrow aisle passage optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kg/220lbs to 200kg/440lbs.

Build-in telescopic arm
From 425kilos/935 lbs to 60 kilos/132 lbs lift capacity at full range Zero turn radius  ideal in confined areas with the short chassis design.

We recommend the lift for

- in store front applications and new construction for larger capacity requirements glazing contractors fire door installers light rail door installation and maintenance in-office partition Installations glass fabricators for in plant use where overhead cranes are unable to reach  loading and unloading trucks.  

The GLG 425 SP-3D in short
The 425-kilos lift is our most popular lift. It has all the features of the biggest lifts for quick and flexible mounting, and still we have succeeded to keep it’s dimensions down so that the lift is as compact and agile as our small lifts.It’s designed to withstand intense usage while offering precision performance.


Click to see printable PDF

GLG420 SP-3D



GLG class “B”: Model 420 SP

Compact and agile self propelled glass lift

The GLG 420 SP is a Self Propelled battery electric drive mobile glass handler capable of picking, transporting and precision placement of 420kilos/924 lbs. Standard equipped with suction cups.

Comparable models

- Model 420 SP can be equipped with accessories like a front lift arm – in comparison the 425 SP 3D has a built-in telescopic arm and is born with a 3D-head for mounting. The 425 SP 3D can be ordered with an optional remote control.

Hydraulic controls provides the operator with the ability to
- feather panels to the millimetre into the opening

Manual handles provides the operator with the ability to

- manually rotate panels 180 degrees clockwise or counter clockwise directions,
- manually swing load to left or right side of machine for side loading when navigating minimal access areas.
- Side load capacity is 100kg/220lbs.
- manual side swing – manual side shift controls providing 76 mm/3 inches left/right from centre adjustments.

Elevator front lift head
 
- lifts loads straight up or down similar to a fork lift

Side load transport

- swing load to left or right side of the machine for narrow aisle passage,
- optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kg/220lbs to 200kg/440lbs.

Optional front lift arm

- 193 kilos/425 lbs lift capacity  handle panels flat from the ground or bench level  turn the panel upside down for table top placement  install skylights overhead as high as 3,2 meters/10.5 ft.

Zero turn radius
 
- ideal in confined areas with the short chassis design.

We recommend the lift for

- in store front applications and new construction for larger capacity requirements
- glazing contractors
- fire door installers
- light rail door installation and maintenance
- in-office partition installations
- glass fabricators
- for in plant use where overhead cranes are unable to reach
- loading and unloading trucks.

The GLG 420 SP in short
Our 420-kilos lift is our low cost entry to our most popular lift-series. It’s built with strength to withstand intense usage. We recommend this lift for users with repetitive installation tasks where the same configuration is used again and again. For users with greater variety and complexity in the mounting tasks, we recommend the 425 SP-3D.


Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG390 SP-TE



GLG class “B”: Model 390 SP-TE

.


Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG360 SP-T



GLG class “B”: Model 360 SP-T




Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG360 SP



GLG class “B”: Model 360 SP

Compact and agile self propelled glass lift


The GLG 360 SP is a Self Propelled battery electric drive mobile glass handler capable of picking, transporting and precision placement of 360 kilos/794 lbs. Standard equipped with suction cups.

Comparable models
-
Model 360 SP can be equipped with accessories like an front lift arm – in comparison the 425 SP 3D has a build-in telescopic arm and is born with a 3D-head for mounting. The 425-kilo lift also comes in a edition with remote control.

Hydraulic controls provides the operator with the ability to
-
feather panels to the millimetre into the opening

Manual handles provides the operator with the ability to
-
manually rotate panels 180 degrees clockwise or counter clockwise directions,
- manually swing load to left or right side of machine for side loading when navigating minimal access areas.
- Side load capacity is 100kg/220lbs.
- manual side swing – manual side shift controls providing 76 mm/3 inches left/right from centre adjustments.

Elevator front lift head
-
lifts loads straight up or down similar to a fork lift

Side load transport
-
swing load to left or right side of the machine for narrow aisle passage,
- optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kg/220lbs to 200kg/440lbs.

Optional front lift arm
-
193 kilos/425 lbs lift capacity
- handle panels flat from the ground or bench level
- turn the panel upside down for table top placement
- install skylights overhead as high as 3,2 meters/10.5 ft.

Zero turn radius
-
ideal in confined areas with the short chassis design.

We recommend the lift for
-
in store front applications and new construction for larger capacity requirements
- glazing contractors
- fire door installers
- light rail door installation and maintenance
- in-office partition installations
- glass fabricators
- for in plant use where overhead cranes are unable to reach
- loading and unloading trucks.

The GLG 360 SP in short
Our 360-kilos lift is our low cost entrance to our most popular lift-series. It’s build with strength to withstand intense usage. We recommend this lift for users with repetitive installation tasks where the lift can be used for many lifts with the same configuration – for users with greater variety and complexity in the mounting tasks, we recommend the 425 SP-3D.


Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG360 MP



GLG class “A”: Model 360 MP
Strong and compact glass lift to operate in confined areas

The GLG 360 MP is a manual push glass lift capable of picking, transporting and precision placement of 360 kilos/794 lbs. Standard equipped with suction cups.

Comparable models

- Model 360 MP is one of our base models which also counts the GLG 210 MP and GLG 310 MP. The three models are identically built, but equipped with different lifting capacities. You can weigh the 360 MP more than 260 kilos/573 lbs down when lifting lighter elements making the lift easier to push around.

Hydraulic controls provides the operator with the ability to

- feather panels to the millimetre into the opening.

Manual handles provides the operator with the ability to

- manually rotate panels 180 degrees clockwise or counter clockwise directions,
- manually swing load to left or right side of machine for side loading when navigating minimal access areas.
- Side load capacity is 100kg/220lbs.
- manual side swing – manual side shift controls providing 76 mm/3 inches left/right from centre adjustments.

Elevator front lift head

- lifts loads straight up or down similar to a fork lift

Side load transport

- swing load to left or right side of the machine for narrow aisle passage
- optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kg/220lbs to 200kg/440lbs.

Adjustable front wheels

- for driving through narrow doorways down to 62 cm/25 inches broad, the front wheels can be put inside in no time - no tools required.

Zero turn radius
 
- ideal in confined areas with the short chassis design.

We recommend the lift for

- in store front applications
- glazing contractors
- fire door installers
- light rail door installation and maintenance
- in-office partition installations
- glass fabricators
- for in plant use where overhead cranes are unable to reach
- loading and unloading “A”-frame glass trucks.

The GLG 360 MP in shortA small and agile lift build with strength to withstand intense usage. It’s aperfect help to glazier’s large variety of tasks, it can move and mount aconsiderable weight of 360 kilos/794 lbs. It's a perfect help to glaziers with a large variety of tasks. All of the quality from Global Lift Group at a very affordable price

Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG310 MP


GLG class “A”: Model 310 MP

Strong and handy glass lift able to operate in confined areas

The GLG 310 MP is a manual push glass lift capable of picking, transporting and precision placement of 310 kilo/683lbs. Standard equipped with suction cups.

Comparable models

- Model 310 MP is one of our base models which also counts the GLG 210 MP and GLG 360 MP. The three models are identically built, but equipped with different lifting capacities. You can weigh the 310 MP more than 200kg/440lbs down when lifting lighter elements making the lift easier to push around.

Hydraulic controls provides the operator with the ability to

- feather panels to the millimetre into the opening

Manual handles provides the operator with the ability to

- manually rotate panels 180 degrees clockwise or counter clockwise directions
- manually swing load to left or right side of machine for side loading when navigating minimal access areas. Side load capacity is 100kg/220lbs.
- manual side swing – manual side shift controls providing 76 mm/3 inches left/right from center adjustments.

Elevator front lift head
 
- lifts loads straight up or down similar to a fork lift

Side load transport

- swing load to left or right side of the machine for narrow aisle passage
- optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kg/220lbs to 200kg/440lbs.

Adjustable front wheels

- for driving through narrow doorways down to 62 cm/25 inches broad, the front wheels can be put inside in no time - no tools required.

Zero turn radius

- ideal in confined areas with the short chassis design.

We recommend the lift for

- in-store front applications
- glazing contractors
- fire door installers
- light rail door installation and maintenance
- in-office partition installations
- glass fabricators
- for in plant use where overhead cranes are unable to reach loading and unloading “A”-frame glass trucks.

The GLG 310 MP in short
A small and agile lift build with strength to withstand intense usage. It’s aperfect help to glazier’s large variety of tasks, it can move and mount a considerable weight of 310 kilo/ 683 lbs. It's a perfect help to glaziers with a large variety of tasks. All of the quality from Global Lift Group at a very affordable price!

Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

GLG210 MP


GLG class "A": Model 210 MP

Super handy glass lift able to operate in confined areas
The GLG 210 MP is a manual push 210 kilo glass lift capable of picking, transporting and precision placing 210 kgs/462 lbs. Standard equipped with suction cups.

Comparable models
-
Model 210 MP is one of our base models which also counts the GLG 310 MP and GLG 360 MP. The three models are identically built, but equipped with different lifting capacities.

Hydraulic control provides the operator with the ability to
-
feather panels to the millimeter into the opening

Manual handles provide the operator with the ability to:
 
- manually rotate panels 180 degrees clockwise or counter clockwise directions
- manually swing load to left or right side of machine for side loading when navigating minimal access areas. Side load capacity is 100kg/220lbs.  
- manual side swing – manual side shift controls providing 76 mm/3 inches left/right from center adjustments.

Elevator front lift head
-
lifts load straight up or down similar to a fork lift

Side load transport
-
swing load to left or right side of the machine for narrow aisle passage
- optional twin wheels can be added to left or right side of machine in minutes for increased side load capacity from 100kgs/220lbs to 200kgs/440lbs

Adjustable front wheels
-
for driving through narrow doorways down to 62 cm/25 inches broad, the front wheels can be put inside in no time - no tools required

Zero turn radius
-
ideal in confined areas with the short chassis design

We recommend the lift for
-
in-store front applications
- glazing contractors
- fire door installers
- light rail door installation and maintenance
- in-office partition installations
- glass fabricators
- for in plant use where overhead cranes are unable to reachloading and unloading "A-frame" glass trucks

The GLG 210 MP in short
A small and agile lift built with strength to withstand intense usage. It's a perfect help to glaziers with a large variety of tasks. All of the quality from Global Lift Group at a very affordable price!

Click to see printable PDF

Accessories available for this model

Permanent lifting hook, extension arm with adjustable lifting hook, fork lift, vertical extension bar, horizontal lifting arm and double wheels

UPCLIMBER


UPCLIMBER

Beside our in-house produced glass lifts, Global Lift Group now distributes the UPCLIMBER-system for light windows to be used at places where the glass lifts doesn’t fit in.

With Upclimber, one man can mount windows up to 130 kg - without heavy lifting. The Upclimber is a compact lifting device, the size of an upper body with handles in the side. It is equipped with a battery-powered engine hinged in a wire and can be mounted with two suction cups. With the wire, the Upclimber can be hung in either a mobile track, which quickly can be mounted on a scaffolding or hung at the top of a one-legged hanger which can lean against the wall where the window is to be mounted.

The idea behind the Upclimber is that you should be able to work alone with the installation of windows up to 130 kilos. If you mount the scaffolding track over the pallet with windows, the Upclimber can lift the window from the pallet onto a trolley that is used to drive the window where it should be mounted.

The upclimber weighs 15 kilos and is fitted with a carrying handle so that it can be carried up and down scaffolding stairs like a small suitcase. During assembly, the Upclimber holds the window in two suction cups at the top of the window. The weight distribution is designed so that the lower part of the window leans toward the frame first so that the window is easy to place in the frame when the suction is disconnected. The scaffolding tracks and the one-legged hanger, called a Jib, and other options like a little fork lift for steel tiles are purchased separately next to the Upclimber.

Click to see printable PDF